manualshive.com logo in svg

Chrysler PACIFICA 2018, Owner'S Manual

Share
Download
Chrysler PACIFICA 2018 Owner'S Manual Download Page 174

Power Outlets

Your vehicle is equipped with 12 Volt (15 Amp) power
outlets, and 5 Volt (2.5 Amp) USB power outlets, that can
be used to power cellular phones, small electronics and
other low powered electrical accessories. The power outlets
can be labeled with either a “key” or a “battery” symbol to
indicate how the outlet is powered. Power outlets labeled
with a “key” are powered when the ignition is in the ON or
ACC position, while the outlets labeled with a “battery”
are connected directly to the battery and powered at all
times.

NOTE:

•

All accessories connected to the “battery” powered
outlets should be removed or turned off when the
vehicle is not in use to protect the battery against
discharge.

CAUTION!

Power outlets are designed for accessory plugs only.
Do not insert any other object in the power outlets as
this will damage the outlet and blow the fuse. Im-
proper use of the power outlet can cause damage not
covered by your New Vehicle Limited Warranty.

The front power outlet is located at the bottom of the
instrument panel.

12 Volt Front Power Outlet

172

GETTING TO KNOW YOUR VEHICLE

Summary of Contents for PACIFICA 2018













































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands