manualshive.com logo in svg

Chrysler PACIFICA 2018, Owner'S Manual

Share
Download
Chrysler PACIFICA 2018 Owner'S Manual Download Page 159

Hose Access Port

The hose access port is located behind the upper access
panel behind the third row seat on the driver’s side.

To Remove Vacuum Hose For Cleaning

1. Unclip the hose from the hose access port located in the

rear of the vehicle by pushing the yellow vacuum hose
release lever with right thumb and lifting the hose with
index finger.

2. Return to vacuum nozzle storage location located be-

hind the sliding door.

3. Grab the vacuum nozzle and gently pull the hose out

through vacuum nozzle storage location.

4. Shake the hose to remove any objects stuck in the hose.

Take care not to perforate the hose while attempting to
dislodge any objects.

5. Reverse the procedure to reinstall and clip the hose into

place.

GARAGE DOOR OPENER — IF EQUIPPED

HomeLink replaces up to three hand-held transmitters that
operate devices such as garage door openers, motorized
gates, lighting or home security systems. The HomeLink
unit is powered by your vehicles 12 Volt battery.

Vacuum System Access Panels

1 — Upper Access Panel
2 — Lower Access Panel

3

GETTING TO KNOW YOUR VEHICLE

157

Summary of Contents for PACIFICA 2018













































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands