manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 486

CAUTION!

Do not use chemical flushes in your air conditioning
system as the chemicals can damage your air condi-
tioning components. Such damage is not covered by
the New Vehicle Limited Warranty.

Refrigerant Recovery And Recycling R134a — If
Equipped

R-134a Air Conditioning Refrigerant is a hydrofluoro-

carbon (HFC) that is endorsed by the Environmental

Protection Agency and is an ozone-saving product. How-

ever, the manufacturer recommends that air conditioning

service be performed by authorized dealer or other

service facilities using recovery and recycling equipment.

NOTE:

Use only manufacturer approved A/C system

PAG compressor oil and refrigerants.

Refrigerant Recovery And Recycling HFO 1234yf
— If Equipped

HFO 1234yf Air Conditioning Refrigerant is a hydro-

fluorocarbon (HFC) that is endorsed by the Environmen-

tal Protection Agency and is an ozone-saving product

with a low GWP (Global Warming Potential). However,

the manufacturer recommends that air conditioning ser-

vice be performed by authorized dealer or other service

facilities using recovery and recycling equipment.

NOTE:

Use only manufacturer approved A/C system

PAG compressor oil and refrigerants.

A/C Air Filter

The filter is located in the fresh air inlet under the hood,

behind a removable panel in the cowl on the passenger

side of the vehicle, next to the windshield wipers. When

installing a new filter, ensure its proper orientation.

484 MAINTAINING YOUR VEHICLE

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands