Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 459

Page: 459 / 574

3. If using another vehicle to jump-start the battery, park

the vehicle within the jumper cables reach, set the

parking brake and make sure the ignition is OFF.

WARNING!

Do not allow vehicles to touch each other as this
could establish a ground connection and personal
injury could result.

Jump-Starting Procedure

WARNING!

Failure to follow this jump-starting procedure could
result in personal injury or property damage due to
battery explosion.

CAUTION!

Failure to follow these procedures could result in
damage to the charging system of the booster vehicle
or the discharged vehicle.

Connecting The Jumper Cables

1. Connect the positive

(+)

end of the jumper cable to the

remote positive

(+)

post of the discharged vehicle.

2. Connect the opposite end of the positive

(+)

jumper

cable to the positive

(+)

post of the booster battery.

3. Connect the negative end

(-)

of the jumper cable to the

negative

(-)

post of the booster battery.

4. Connect the opposite end of the negative

(-)

jumper

cable to the

remote

negative

(-)

post of the vehicle with

the discharged battery.

WHAT TO DO IN EMERGENCIES 457

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands

Chrysler 300 Touring RWD 2010, Owner'S Manual

Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands