manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 414

4. For each subsequent ignition switch cycle, a chime will

sound, the TPM Telltale Light will flash on and off for

75 seconds and then remain on solid, and the DID will

display a

#

SERVICE TPM SYSTEM

#

message for a

minimum of five seconds and then display dashes (- -)

in place of the pressure value.

5. Once you repair or replace the original road tire and

reinstall it on the vehicle in place of the compact spare,

the TPMS will update automatically. In addition, the

TPM Telltale Light will turn OFF and the graphic in

the DID will display a new pressure value instead of

dashes (- -), as long as no tire pressure is below the

low-pressure warning limit in any of the four active

road tires. The vehicle may need to be driven for up to

20 minutes above 15 mph (24 km/h) in order for the

TPMS to receive this information.

General Information

This device complies with Part 15 of the FCC rules and

RSS 210 of Industry Canada. Operation is subject to the

following conditions:

•

This device may not cause harmful interference.

•

This device must accept any interference received,

including interference that may cause undesired op-

eration.

The TPM sensors are regulated under one of the follow-

ing licenses:

United States

MRXMERCTX1

Canada

2546A-MERCTX1

412 STARTING AND OPERATING

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands