Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 354

Page: 354 / 574

In the event of a momentary problem, the transmission

can be reset to regain all forward gears by performing the

following steps:

NOTE:

In cases where the instrument cluster message

indicates the transmission may not re-engage after en-

gine shutdown, perform this procedure only in a desired

location (preferably, at your authorized dealer).
1. Stop the vehicle.
2. Shift the transmission into PARK, if possible. If not,

shift the transmission to NEUTRAL.

3. Push and hold the ignition switch until the engine

turns OFF.

4. Wait approximately 30 seconds.
5. Restart the engine.

6. Shift into the desired gear range. If the problem is no

longer detected, the transmission will return to normal

operation.

NOTE:

Even if the transmission can be reset, we recom-

mend that you visit your authorized dealer at your

earliest possible convenience. Your authorized dealer has

diagnostic equipment to determine if the problem could

recur.
If the transmission cannot be reset, authorized dealer

service is required.

AUTOSTICK — IF EQUIPPED

AutoStick is a driver-interactive transmission feature

providing manual shift control, giving you more control

of the vehicle. AutoStick allows you to maximize engine

braking, eliminate undesirable upshifts and downshifts,

and improve overall vehicle performance. This system

352 STARTING AND OPERATING

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands

Chrysler 300 Touring RWD 2010, Owner'S Manual

Search results

Summary of Contents for 300 Touring RWD 2010

Reviews:

Brands by name

Popular brands