manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 205

NOTE:

•

The system will retain the last setting selected by the

driver after ignition shut down.

•

FCW may not react to irrelevant objects such as

overhead objects, ground reflections, objects not in the

path of the car, stationary objects that are far away,

oncoming traffic, or leading vehicles with the same or

higher rate of speed.

•

FCW will be disabled like ACC, with the unavailable

screens.

FCW Limited Warning

If the DID displays “ACC/FCW Limited Functionality”

or “ACC/FCW Limited Functionality Clean Front Wind-

shield” momentarily, there may be a condition that limits

FCW functionality. Although the vehicle is still drivable

under normal conditions, the active braking may not be

fully available. Once the condition that limited the sys-

tem performance is no longer present, the system will

return to its full performance state. If the problem per-

sists, see your authorized dealer.

Service FCW Warning

If the system turns off, and the DID displays:

•

ACC/FCW Unavailable Service Required

•

Cruise/FCW Unavailable Service Required

This indicates there is an internal system fault. Although

the vehicle is still drivable under normal conditions, have

the system checked by an authorized dealer.

LANESENSE — IF EQUIPPED

LaneSense Operation

The LaneSense system is operational at speeds above

37 mph (60 km/h) and below 112 mph (180 km/h). The

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands