manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 152

Lights-On Reminder

If the headlights or parking lights are on after the ignition

is placed in the OFF position, a chime will sound to alert

the driver when the driver’s door is opened.

Fog Lights — If Equipped

Front Fog Lights — If Equipped

The front fog light switch is built into the headlight

switch.

To activate the front fog lights, turn on the parking

lights or the low beam headlights and push the

headlight switch. To turn off the front fog lights, either

push the headlight switch a second time or turn off the

headlight switch.

Fog Light Switch

150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands