manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Owner'S Manual

Share
Download
Chrysler 300 Touring RWD 2010 Owner'S Manual Download Page 118

“Slide-On-Rod” And Extender Features Of Sun
Visor

To use the “Slide-On-Rod” feature of the sun visor, rotate

the sun visor downward and swing the sun visor so it is

parallel to the side window, grab the sun visor and pull

rearwards until the sun visor is in the desired position. To

use the extender feature of the sun visor, grab the

extender which is located at the rear of the visor and pull

rearward.

Illuminated Vanity Mirror

Slide-On-Rod Feature

116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands