Chrysler 300 2017 Owner'S Manual Download Page 45 | Manualshive

Page: 45 / 488

background image

Lap/Shoulder Belt Untwisting Procedure

Use the following procedure to untwist a twisted lap/
shoulder belt.

1. Position the latch plate as close as possible to the anchor

point.

2. At about 6 to 12 in (15 to 30 cm) above the latch plate,

grasp and twist the seat belt webbing 180 degrees to
create a fold that begins immediately above the latch
plate.

3. Slide the latch plate upward over the folded webbing.

The folded webbing must enter the slot at the top of the
latch plate.

4. Continue to slide the latch plate up until it clears the

folded webbing and the seat belt is no longer twisted.

Adjustable Upper Shoulder Belt Anchorage

In the driver and front passenger seats, the top of the
shoulder belt can be adjusted upward or downward to
position the seat belt away from your neck. Push or
squeeze the anchorage button to release the anchorage, and
move it up or down to the position that serves you best.

As a guide, if you are shorter than average, you will prefer
the shoulder belt anchorage in a lower position, and if you
are taller than average, you will prefer the shoulder belt
anchorage in a higher position. After you release the
anchorage button, try to move it up or down to make sure
that it is locked in position.

Adjustable Anchorage

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

43

«
...
43
44
45
46
47
...
»

Summary of Contents for 300 2017









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 2017

Brand: Dometic GROUP Pages: 20

Brand: Porsche Pages: 195

Brand: Audi Pages: 9

Brand: Belkin Pages: 4

Brand: EUFAB Pages: 52

Brand: Uebler Pages: 56

Brand: XTC Pages: 4

Brand: Menabo Pages: 12

Brand: StowAway 2 Pages: 2

Challenger 2013

Brand: Dodge Pages: 543

BASIC TLL171231

Brand: Tellur Pages: 5

Brand: Beper Pages: 52

Brand: Thule Pages: 12

Brand: BraunAbility Pages: 46

Brand: Thule Pages: 4

Brand: Saab Pages: 37

Brand: Reliant Pages: 116

Brand: Quadratec Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands