manualshive.com logo in svg

Chrysler 300 2017, Owner'S Manual

Share
Download
Chrysler 300 2017 Owner'S Manual Download Page 366

ADDING FUEL

1. Push the fuel filler door release switch (located in the

driver’s door map pocket).

2. Open the fuel filler door.

NOTE:

In certain cold conditions, ice may prevent the fuel

door from opening. If this occurs, lightly push on the fuel
door to break the ice buildup and re-release the fuel door
using the inside release button. Do not pry on the door.

3. There is no fuel filler cap. A flapper door inside the pipe

seals the system.

4. Insert the fuel nozzle fully into the filler pipe – the

nozzle opens and holds the flapper door while refuel-
ing.

NOTE:

Only the correct size nozzle opens the latches

allowing the flapper door to open.

Fuel Filler Door Release Switch

Fuel Filler Door

364

STARTING AND OPERATING

Summary of Contents for 300 2017









































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands