manualshive.com logo in svg

Chrysler 300 2017, Owner'S Manual

Share
Download
Chrysler 300 2017 Owner'S Manual Download Page 267

AUX/USB/MP3 CONTROL

This feature allows an external USB device to be plugged
into the USB port.

For further information, refer to the Uconnect Owner’s
Manual Supplement.

Located on the rear of the front center console are dual USB
“Charge Only” ports.

The USB “Charge Only” ports will recharge battery oper-
ated USB devices when connected.

Uconnect 8.4/8.4 NAV AUX/USB Ports

1 — USB Port
2 — Aux Jack
3 — USB Port

Rear USB Charging Ports

4

UNDERSTANDING YOUR INSTRUMENT PANEL

265

Summary of Contents for 300 2017









































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands