Chrysler 2012 Town & Country Owner'S Manual Download Page 53

Page: 53 / 652

Sliding Side Door Child Protection Lock

To provide a safer environment for small children riding
in the rear seats, the sliding doors are equipped with a
Child Protection Door Lock system.

NOTE:

When the Child Protection Door Lock system is

engaged, the door can be opened only by using the
outside door handle even though the inside door lock is
in the unlocked position.

To Engage the Child Protection Door Lock

1. Open the sliding side door.

Overhead Console Power Sliding Door Master Switch

1 — Left Sliding Door

3 — Right Sliding Door

2 — Liftgate

4 — Master Lock

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2012 Town & Country

Reviews:

Chrysler 2012 Town & Country, Owner'S Manual, Page: 53 / 652

Search results

Summary of Contents for 2012 Town & Country

Reviews: