manualshive.com logo in svg

Chrysler 2012 Town & Country, Owner'S Manual, Page: 48 / 652

Share
Download
Chrysler 2012 Town & Country Owner'S Manual Download Page 48

NOTE:

The switches will not operate if the driver has

activated the Power Window Lockout.

NOTE:

The sliding door windows do not fully open,

stopping several inches above the window sill.

Wind Buffeting

Wind buffeting can be described as the perception of
pressure on the ears or a helicopter-type sound in the
ears. Your vehicle may exhibit wind buffeting with the
windows down, or the sunroof (if equipped) in certain
open or partially open positions. This is a normal occur-
rence and can be minimized. If the rear windows are
open and buffeting occurs, open the front and rear
windows together to minimize the buffeting. If the
buffeting occurs with the sunroof open, adjust the sun-
roof opening to minimize the buffeting.

SLIDING SIDE DOOR

The sliding door may be opened from the inside or the
outside. Pull outward on the exterior handle to open the
sliding door. The sliding door inside handle functions by
rocking forward and back. Rocking the handle back-
wards opens the door and rocking forward releases the
hold open latch in order to close the door.

Sliding Door Power Window Switch

46

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments