manualshive.com logo in svg

Chrysler 2012 Town & Country, Owner'S Manual, Page: 379 / 652

Share
Download
Chrysler 2012 Town & Country Owner'S Manual Download Page 379

Remote Control Storage

The video screen(s) come with a built in storage compart-
ment for the remote control which is accessible when the
screen is opened. To remove the remote, use your index
finger to pull and rotate the remote towards you. Do not
try to pull the remote straight down as it will be very
difficult to remove. To return the remote back into its
storage area, insert one long edge of the remote into the
two retaining clips first, and then rotate the remote back
up into the other two retaining clips until it snaps back
into position.

The Remote Control Storage

4

UNDERSTANDING YOUR INSTRUMENT PANEL

377

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments