manualshive.com logo in svg

Chrysler 2012 Town & Country, Owner'S Manual, Page: 365 / 652

Share
Download
Chrysler 2012 Town & Country Owner'S Manual Download Page 365

Listen To An Audio Source On Channel 2 While A
Video Is Playing On Channel 1

Ensure the Remote Control and Headphone switch is on
Channel 2.

Using The Remote Control

1. Press the MODE button on the Remote Control and
the Mode Select Screen will display, unless a video is
playing then only a small banner will appear on the
bottom of the screen.

2. While looking at the video screen, either press Up/
Down/Left/Right on the Remote Control to highlight the
desired audio source or repeatedly press the MODE
button on the remote until the desired audio source
appears on the screen.

Select FM Mode On The VES Screen

4

UNDERSTANDING YOUR INSTRUMENT PANEL

363

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments