manualshive.com logo in svg

Chrysler 2012 Town & Country, Owner'S Manual, Page: 32 / 652

Share
Download
Chrysler 2012 Town & Country Owner'S Manual Download Page 32

REMOTE STARTING SYSTEM — IF EQUIPPED

This system uses the Remote Keyless Entry
(RKE) transmitter to start the engine conve-
niently from outside the vehicle while still
maintaining security. The system has a range of

approximately 300 ft (91 m).

NOTE:

•

The vehicle must be equipped with an automatic
transmission to be equipped with Remote Start.

•

Obstructions between the vehicle and the Key Fob
may reduce this range.

How To Use Remote Start

All of the following conditions must be met before the
engine will Remote Start:

•

Shift lever in PARK

•

Doors closed

•

Hood closed

•

Liftgate closed

•

Hazard switch off

•

Brake switch inactive (brake pedal not pressed)

•

Ignition key removed from ignition switch

•

Battery at an acceptable charge level

•

RKE PANIC button not pressed

•

System not disabled from previous remote start event

•

Vehicle theft alarm not active

•

Ignition in Off position (Keyless Enter-N-Go)

30

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments