Chrysler 2006 300C SRT8 Owner'S Manual Download Page 171 | Manualshive

Page: 171 / 320

background image

and thus remain a part of the AM reception. They
interfere very little with the frequency variations that
carry the FM signal.

AM Reception

AM sound is based on wave amplitude, so AM reception
can be disrupted by such things as lightning, power lines
and neon signs.

FM Reception

Because FM transmission is based on frequency varia-
tions, interference that consists of amplitude variations
can be filtered out, leaving the reception relatively clear,
which is the major feature of FM radio.

NOTE:

On vehicles so equipped the radio, steering

wheel radio controls and 6 disc CD/DVD changer if
equipped, will remain active for 10 minutes after the
ignition has been turned off, and the driver door has not
been opened. This feature is programmable through the
electronic vehicle information center (EVIC) — if
equipped. Refer to “Delay Power Off to Accessories Until
Exit” under “Personal Settings” in the Electronic Vehicle
Information Center section for details.

CASSETTE TAPE AND PLAYER MAINTENANCE

To keep the cassette tapes and player in good condition,
take the following precautions:

1. Do not use cassette tapes longer than C-90; otherwise,
sound quality and tape durability will be greatly dimin-
ished.

2. Keep the cassette tape in its case to protect from
slackness and dust when it is not in use.

3. Keep the cassette tape away from direct sunlight, heat
and magnetic fields such as the radio speakers.

4. Before inserting a tape, make sure that the label is
adhering flatly to the cassette.

5. A loose tape should be corrected before use. To rewind
a loose tape, insert the eraser end of a pencil into the tape
drive gear and twist the pencil in the required directions.

Maintain your cassette tape player. The head and capstan
shaft in the cassette player can pick up dirt or tape
deposits each time a cassette is played. The result of
deposits on the capstan shaft may cause the tape to wrap
around and become lodged in the tape transport. The

UNDERSTANDING YOUR INSTRUMENT PANEL

171

4

«
...
169
170
171
172
173
...
»

Summary of Contents for 2006 300C SRT8

































































































































































































































































































































Reviews:

No comments

Related manuals for 2006 300C SRT8

Brand: Yakima Pages: 12

Brand: JEHNERT SOUND DESIGN Pages: 8

Experience Series

Brand: Rainbow Pages: 19

Brand: Yakima Pages: 12

Brand: PEUGEOT Pages: 128

Brand: Schumacher Electric Pages: 87

2009 ESCALADE ESV

Brand: Cadillac Pages: 602

Brand: FORM FIT Pages: 2

Edge Flush Rail

Brand: Thule Pages: 12

Brand: Uebler Pages: 56

Brand: Nav TV Pages: 5

Ram Commercial2016

Brand: Dodge Pages: 675

Brand: Opel Pages: 32

Brand: Reese Explore Pages: 9

Brand: MVG Pages: 18

Brand: KEKO Pages: 13

Stealth 4191F Series

Brand: Road Armor Pages: 5

Fleetwood Brougham Sedan 1966

Brand: Cadillac Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands