Chromalox MOS Series Installation & Operation Manual Download Page 10

10

© 2014 Chromalox, Inc.

Renewal Parts Identification

Gasket

Size (In.)

Rating

304639-007

2

150#

304639-009

3

150#

Miscellaneous

Description

118661-037

Discharge Pressure Gauge

118661-038

Suction Pressure Gauge

122571-076

Process Thermocouple

305910-005

Overtemperature Thermocouple

Limited Warranty:

Please refer to the Chromalox limited warranty applicable to this product at

http://www.chromalox.com/customer-service/policies/termsofsale.aspx.

Chromalox, Inc.

2150 N. Rulon White Blvd.

Ogden, UT 84404

(800) 368-2493

www.chromalox.com

Start-Up Supervision

Factory trained personnel are highly recommended 

for those customers who are unfamiliar with the initial 

start-up.

Contact your local Chromalox sales office or call the 

Chromalox Service Center: 1-800-443-2640.

Maintenance

Factory trained personnel are recommended for those 

unfamilar with proper system maintenance.

Contact your local Chromalox sales office or call the 

Chromalox Service Center: 1-800-443-2640.

Maximum Temperatures

DO NOT attempt to operate any heat transfer system 

or heat transfer oil at temperatures higher than those 

recommended by the manufacturer.
Chromalox heat transfer systems are designed for a 

particular maximum temperature. If you do not know 

this design temperature, check with the Chromalox 

factory or consult the individual instruction sheet for 

that system. Exceeding the designed temperature of 

the heat transfer system will void the warranty.
Exceeding the temperature limits of the heat transfer 

fluid will cause its thermal breakdown or degradation. 

This will result in the formation of sludge in the system 

and carbon on the heating elements and eventually 

cause pump and heater failure. If you do not know this 

maximum temperature, check with the fluid manufac-

turer.

In hazardous or explosive areas, the pipe sur-

faces of oil type heat transfer systems could 

achieve temperatures higher than allowed for 

Class I, Group d, division I.

For replacement heater bundle or spare parts not listed in this instruction sheet, please contact Chromalox 

Customer Service Center. 1-800-443-2646

Summary of Contents for MOS Series











Reviews: