manualshive.com logo in svg

Chromalox MiniMax 1, User Manual, Page: 25 / 28

Share
Download
Chromalox MiniMax 1 User Manual Download Page 25

- 23 -

© 2021 Chromalox

®

, Inc.

1-888-996-9258

MiniMax 1 Ordering Information

Model 

SCR Power Pack

Mmax 1

Single Phase SCR Power Controller Complete with Lugs and I

2

T Fusing

1, 2

Code

Control Configuration

5

Proportional Control, DOT Zero-Crossover Firing, Command Input Signals: 4-20mA, 

0-5 VDC, 1-5 VDC (via Modbus RTU/485 only), 0-10 VDC, Remote 0-1000 OHM Po-

tentiometer w/Manual Override, Modbus RTU/RS485 Communications. RTD Heat Sink 

Temperature Sensor with Two Set-Points, Automatic Line Sensing 50/60HZ, Remote 

Permissive Stop Input, Form “C” Dry Contact Alarm Output, Staged Heating w/Digital 

Calibration Zero / Span Adjustments(4-8 mA, 8-12 mA,12-16 mA,16-20 mA (via Modbus 

RTU/RS485 only), LED Diagnostics: Command Input, Main/Trigger Boards  Running, 

SCR Status per Phase, Diagnostic Kit via Modbus RTU/RS485: Highest Heat Sink 

Temperature, Last Heat Sink Temperature, Highest and Lowest Ambient Temperature, 

Line Frequency Monitoring, Third Party Certifications: UL, cUL, CE, DEMKO (650 A 

and below).

Code Current at 50˚C (104˚F) Ambient

01

30 Amp

02

50 Amp

03

75 Amp

Code

Line Voltage

1

120 - 480Vac

2

575Vac

Code Instrument Power

1

120 to 240Vac 50/60Hz

Code Remote Manual Adjust/Auto Manual Switch

3

0

None

1

Pot with 0 - 100% dial and local/Remote Switch, 

Single Turn 1K ohm Potentiometer (Requires 

Proportional Board)

Mmax I -

5

01 

1 

1

0 

Typical Model Number 

 

1)  SCR Fusing is for semiconductor protection only, not wire protection.

2)  Supplied loose for customer mounting. 575V Fusing only

3)  Supplied loose for customer mounting

Note:

Storage Temperature 14ºF to 158ºF (-10ºC to 70ºC). 

 

CE application requires filters.

Chromalox Part Numbers

0005-60055 — Line filter, single phase, 230VAC

0005-60057 — Line filter, 120-230VAC

CE application requires filter.

Summary of Contents for MiniMax 1





























Reviews:

No comments