manualshive.com logo in svg

Chromalox IntelliTrace ITC 2, Installation & Operation Manual, Page: 22 / 32

Share
Download
Chromalox IntelliTrace ITC 2 Installation & Operation Manual Download Page 22

22

Parameter Defaults, Min., Max. & Range & User Settings

Screen Menu & Parameter
6. Comms Menu

Default

Min.

Max.

Also

User Settings

Baud Rate

9.6k

2.4k, 4.8k, 9.6k, 19.2k, 38.4k, 56.0k

Parity

None

Even

Odd

None

ModBus ID

1

1

255

IP Address

Optional Feature

DHCP

Use

Use

Do Not Use

7. Systems Menu

Default

Min.

Max.

Range

User Settings

Firmware Version

Current Firmware Version

Button Sound

On

Off

On

Units

Fahrenheit

Fahrenheit

Celsius

Temperature Sensing 1

Single

Single, Average, Low, High

Temperature Sensing 2

Single

Single, Average, Low, High, 

Use 1 RTD to control both circuits

Failed Sensor Output 1

50%

0%

100%

Failed Sensor Output 2

50%

0%

100%

Password Level 1

Password Inputs

Password Level 2
Password Level 3

Alarm State

Normally 

Closed

Normally 

Open

Normally 

Closed

Restore to Default

Disabled

Up / Down

Up / Down

Summary of Contents for IntelliTrace ITC 2

































Reviews:

No comments