manualshive.com logo in svg

Chromalox IntelliTrace ITC 2, Installation & Operation Manual, Page: 12 / 32

Share
Download
Chromalox IntelliTrace ITC 2 Installation & Operation Manual Download Page 12

12

The Control Menu

Security Level 3

The Current Menu

Security Levels 2 & 3

The Current Menu provides access to the current and 

GFEP based parameters:  Low Current Alarm, High 

Current Alarm, GFEP Setpoint & GFEP Alarm/Trip for 
Circuits 1 and 2 (when available).

4.  Current Menu

Low 

Current 

Alarm

Lower limit of the Load Current Variable at 

which the system goes into alarm state. 

This alarm may be turned OFF by going 

one increment beyond the Lowest setting.

High 

Current 

Alarm

Upper limit of the Load Current Variable at 

which the system goes into alarm state. 

This alarm may be turned OFF by going 

one increment beyond the Highest setting.

GFEP 

Setpoint

Upper limit of the Ground Fault Equipment 

Protection Variable at which the system 

goes into alarm state

GFEP 

Alarm/Trip

Action taken by controller when the GFEP 

Setpoint alarm condition is achieved.  

The options are:

1. Alarm Only,

    Non-Latching

Output remains at 

selected output %. 

Alarm clears when 

sensed GFEP cur-

rent is 5mA < GFEP 

setpoint

2. Alarm & Trip,

    Non-Latching

Output goes to 0% 

(off) while in alarm 

state. Alarm clears 

when sensed GFEP 

current is 5mA <GFEP 

setpoint

3. Alarm Only,

    Latching

Output remains at 

selected output %. 

Alarm condition may 

only be cleared with a 

manual reset.

4. Alarm & Trip,

    Latching

Output goes to 0% 

(Off) while in alarm 

state. Alarm condition 

may only be cleared 

with a manual reset.

Summary of Contents for IntelliTrace ITC 2

































Reviews:

No comments