manualshive.com logo in svg

Chromalox CX224, Setup Tutorial, Page: 13 / 17

Share
Download
Chromalox CX224 Setup Tutorial Download Page 13

Chromalox  Tel: 615-793-3900  •  Fax: 615-793-3563  •  www.chromalox.com 

13

 

 

3.  Definition of Terms / Use for Operation 
 
A) Menu 

1.  Monitor Zones  

Select this option to return to Monitoring Mode to read and evaluate 
the inputs and outputs. 

 

2.  Configuration Menu 

The Configuration Menu may require a password to enter, by default no password is 
required.  The Configuration Menu contains the following options. 

1.

 

Change Passwords  

2.

 

Setup  

3.

 

Modify Offsets  

4.

 

Comm Settings 

 

1.  

Change Passwords -

 Select the password to change.  A message 

asking if you would like to change a password will be shown.  Choose 
‘Yes’ to change a password or ‘No’ to exit the Change Passwords option.  
By setting a password to 0000, the password will be deactivated.  The 
valid range for a password is 0000 to 9999.  If a password is already 
entered, the user will be required to enter the existing password in 
order to change it.  If you forget your password, the master password 
can be used, it is found on the last page of this manual.  Available 
selections are: 

1.

 

Program Password  

2. Unlatch 

Password 

 

1.

 

Program Password

 – Changes the password that is used 

to protect the Change Program option. 

2.

 

Unlatch Password 

– Changes the password that is used 

to protect Manual Reset of the Outputs. 

 

2. Setup 

- This section is used to configure all inputs and outputs. (May 

be password protected.)  When this section is exited, either due to the 
60-second timeout or exited by the user, the CX224 will automatically 
reset and start scanning with the new program settings.  The CX224 will 
also reset when program settings are changed via the communications 
link using Chromalox’s CX224 Software.  This is the main section of the 
CX224 configuration process and has a full section below covering its 
use.  See section 4B, Entering the Program Settings, for more 
information. 
 

http://www.chromalox.com

Summary of Contents for CX224


















Reviews:

No comments