manualshive.com logo in svg

Christie Spyder X20, User Manual

Share
Download
Christie Spyder X20 User Manual Download Page 61

 

 

License Management 

Spyder X20 User Manual 

61 

020-000916-01 Rev. 1 (04-2016) 

VIEWING CURRENT LICENSE OPTIONS 

1.

 

From within Advanced, open the License Manager (Help 

 License Manager). 

2.

 

From the Welcome screen, select the ‘View licenses previously applied to my system(s)’, and then click 
‘Next’.

 

3.

 

The View Existing License screen contains a dropdown list, which lists each Spyder frame currently 
detected on the same network as the client PC.  The license manager automatically downloads and 
displays the state of all license options from a remote Spyder system when an IP address is selected.  

Click ‘Finish’ to close the license manager after viewing any desired Spyder licenses.

 

Available Options for Spyder 

The item(s) listed below provide a brief introduction to the various license protected features for Spyder.  For 
more information on any of the items below, or for information on purchasing one or more of the licensed 
options, contact Christie technical support at: 

http://www.christiedigital.com/en-us/product-support/support-offices/Pages/default.aspx

 

Maintenance Contract 

In addition to providing extended hardware coverage and support services, maintenance contracts purchased 
for the Spyder system enable owners to access software updates containing new features and functionality.  A 
license containing an active maintenance contract is required to update to new software versions at and above 
version 3.0. 

Stereoscopic (SSO) 

New and existing Spyder customers can extend the power of the Spyder hardware platform by incorporating 
stereoscopic input and output processing capabilities.  The stereoscopic option for Spyder allows for any 
combination of 2D video inputs and 3D (active or passive) stereoscopic inputs to be displayed on the same 
screen simultaneously.  Spyder outputs also support passive or active stereoscopic modes, allowing Spyder to 
natively run 3D display devices. 

Summary of Contents for Spyder X20













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands