Christie Roadie 4K35 Service Manual Download Page 73 | Manualshive

Page: 73 / 87

background image

6. Remove the rod ball joint by unscrewing it from the lamp adjuster assembly.
7. Loosen the four captive screws securing the lamp adjust to the baseplate.

8. Remove the lamp adjuster assembly through the lamp door.
9. To complete the installation, repeat these steps in reverse order.
10. Perform a lamp calibration.

Replacing the centrifugal fan interface board

Estimated replacement time: 5 minutes

1. Remove the rear lens-side cover (on page 43).
2. Disconnect the cable connections P1, P3,a nd P4.
3. Remove the four hex head screws securing the centrifugal fan interface board (CFIB).
4. Remove the CFIB.
5. To install the CFIB, repeat these steps in reverse order.

Power supplies

Learn how to replace power related components.

Replacing the igniter

Estimated replacement time: 35 m 10 minute calibration
When installing the positive and negative igniter harness leads to the igniter, do not over tighten the
M10 screw to avoid bending the metal connection plates attached to the igniter.

Parts and module replacement

Roadie 4K35 and 4K45 Service Manual

73

020-101694-03 Rev. 1 (01-2016)

Copyright

©

2016 Christie Digital Systems USA Inc. All rights reserved.

«
...
71
72
73
74
75
...
»

Summary of Contents for Roadie 4K35
























































































Reviews:

No comments

Related manuals for Roadie 4K35

Brand: Da-Lite Pages: 8

BarcoReality 908

Brand: Barco Pages: 4

Brand: Barco Pages: 2

Brand: Barco Pages: 50

MultiSync MT1020

Brand: NEC Pages: 7

Brand: Panamax Pages: 1

Brand: Professional Audio Equipment Pages: 6

Brand: promethean Pages: 58

Brand: Optoma Pages: 1

VIDEOMATE 2030P

Brand: Navitar Pages: 18

Learn Big IN37EP

Brand: InFocus Pages: 39

Brand: Panasonic Pages: 17

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 7

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 54

Brand: Panasonic Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands