Christie Roadie 4K35 Service Manual Download Page 51

Page: 51 / 87

7. Replace the fans.
8. To re-install, follow these steps in reverse order.

Replacing the igniter fan (fan #16)

Estimated replacement time: 5 minutes per fan

1. Remove the rear lens side cover.
2. Disconnect the fan inline connector.
3. Remove the four screws securing the fan.

4. Remove the igniter fan and its safety cover.
5. Replace the igniter fan.
6. To re-install the igniter fan, follow these steps in reverse order.

Replacing the HIP fan (fan #13)

Estimated replacement time: 16 minutes per fan

1. Remove the card cage.
2. Disconnect the fan inline connector.
3. Remove the four screws securing the fan.

Parts and module replacement

Roadie 4K35 and 4K45 Service Manual

020-101694-03 Rev. 1 (01-2016)

Summary of Contents for Roadie 4K35
























































































Search results

Summary of Contents for Roadie 4K35

Reviews:

Related manuals for Roadie 4K35

Brands by name

Popular brands

Christie Roadie 4K35, Service Manual

Search results

Summary of Contents for Roadie 4K35

Reviews:

Related manuals for Roadie 4K35

Brands by name

Popular brands