Christie Roadie 4K35 Service Manual Download Page 50 | Manualshive

Page: 50 / 87

background image

4. Remove two screws securing the fan to the bracket.
5. Remove the fan.
6. To re-install, follow these steps in reverse order.

Replacing the card cage fan-back (fan #9)

Estimated replacement time: 16 minutes

1. Remove the front top cover (on page 40).
2. Remove the light engine cover (on page 41).
3. Remove two screws securing the fan to the card cage.

4. Disconnect the inline connector.
5. Remove the card cage fan.
6. To re-install, follow these steps in reverse order.

Replacing the card cage intake fans–top (fan #10, 11 and 12)

Estimated replacement time: 4 minutes per fan

1. Remove the front top cover (on page 40).
2. Remove the light engine cover (on page 41).
3. Disconnect the required fan harnesses from the primary EVB board.
4. Disconnect the inline fan connector(s) and release the cables from the routing clip.
5. Remove the four screws for each fan.
6. Remove the fan(s).

Parts and module replacement

Roadie 4K35 and 4K45 Service Manual

50

020-101694-03 Rev. 1 (01-2016)

Copyright

©

2016 Christie Digital Systems USA Inc. All rights reserved.

«
...
48
49
50
51
52
...
»

Summary of Contents for Roadie 4K35
























































































Reviews:

No comments

Related manuals for Roadie 4K35

Graphics 808s R9000904

Brand: Barco Pages: 51

Brand: Intermatic Pages: 4

Brand: IGNIA LIGHT Pages: 16

Brand: Remaco Pages: 3

Brand: KVANT Pages: 15

BARCOREALITY SIM 6 MK II + WARP 6

Brand: Barco Pages: 157

Brand: Honeywell Pages: 17

Brand: Honeywell Pages: 241

POA-MD18DVI - Projector Terminal Expansion Board

Brand: Sanyo Pages: 1

Brand: Sanyo Pages: 2

Brand: Sanyo Pages: 2

Brand: Sanyo Pages: 2

Brand: Sanyo Pages: 2

Brand: Sanyo Pages: 3

Brand: Sanyo Pages: 3

Brand: Sanyo Pages: 4

WF10 - PLV WXGA LCD Projector

Brand: Sanyo Pages: 56

Think GAIA PLC-XE45

Brand: Sanyo Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands