Christie Roadie 4K35 Service Manual Download Page 42

Page: 42 / 87

Removing the rear top lid

The rear top cover provides access to the low profile extractor, reflector and heat dump, and other

components.
Estimated replacement time: 5 minutes

1. Shut down the projector (on page 22).
2. Remove the front cover (on page 40).
3. Remove the four screws securing the rear top cover.
4. Remove the cover.

5. To re-install, follow these steps in reverse order.

Removing the front lamp-side cover

Estimated replacement time: 1 minutes

1. Shut down the projector (on page 22).
2. Remove the shroud, if installed (on page 40).
3. Loosen the three captive screws securing the cover.

4. Pull the cover up to clear the bottom tabs and remove.
5. To re-install, align the bottom tabs and follow these steps in reverse order.

Removing the lamp door

Remove the lamp door to access the lamp compartment.
Estimated replacement time: 1 minutes

Parts and module replacement

Roadie 4K35 and 4K45 Service Manual

020-101694-03 Rev. 1 (01-2016)

Summary of Contents for Roadie 4K35
























































































Search results

Summary of Contents for Roadie 4K35

Reviews:

Related manuals for Roadie 4K35

Brands by name

Popular brands

Christie Roadie 4K35, Service Manual

Search results

Summary of Contents for Roadie 4K35

Reviews:

Related manuals for Roadie 4K35

Brands by name

Popular brands