Christie Roadie 4K35 Service Manual Download Page 36

Page: 36 / 87

•

Cloth wipes

•

Protective clothing/safety gear (required when handling lamp), includes:

•

598900-095 protective clothing

•

Face shield

•

Vinyl-coated or interlock knit-lined gloves

•

Nylon flak jacket

Index of parts and modules

Only use the recommended parts when servicing the projector.

Description

Part number

Shroud

129-112105-XX

Front top lid

—

Light engine lid

—

Rear top lid

—

Front lamp-side cover

—

Lamp door

—
003-003081-XX (low security lock)

Front lens-side cover

—

Rear lens-side cover

—

Rear cover

—

Front cover

—
003-001515-XX (knock-out plate)

Touch panel controller (TPC)

003-105305-XX
003-111169-XX (harness)
003-003326-XX (mount)

Light engine air filter

003-005010-XX

Laminar airflow device (LAD) filter

03-001982-51P (3pk)

Card cage exhaust fans—bottom (fan #1 and 2)

003-110827-XX

Radiator fan (Fan #3)

003-112339-XX

LAD fan (fan #4)

003-111697-XX

Light engine fan pack (fan #5, 6,7 And 8)

003-110827-XX

Light engine fan (fan #15)

003-110854-XX

Card cage fan—back (fan #9)

003-111609-XX

Card cage intake fans—top (fan #10, 11 And 12)

003-111709-XX

Main AC blower

003-105346-XX

Parts and module replacement

Roadie 4K35 and 4K45 Service Manual

020-101694-03 Rev. 1 (01-2016)

Summary of Contents for Roadie 4K35
























































































Search results

Summary of Contents for Roadie 4K35

Reviews:

Related manuals for Roadie 4K35

Brands by name

Popular brands

Christie Roadie 4K35, Service Manual

Search results

Summary of Contents for Roadie 4K35

Reviews:

Related manuals for Roadie 4K35

Brands by name

Popular brands