Christie DHD630-GS Service Manual Download Page 61

Page: 61 / 79

Electronics

GS Series 630-635 Service Manual

020-001224-02 Rev. 1 (08-2018)

1. Remove the top cover.

See

Removing the top cover

on page 51.

2. Remove the main board and I/O board.

See

Replacing the main board and I/O board

on page 69.

3. Remove the rear cover.

See

Removing the rear cover

on page 52.

4. Remove the fan 4.

See

Replacing fans 4 and 5

on page 58.

5. Unplug the connector for the thermal switch cable.

6. To remove the thermal switch, remove one M3 screws with a Phillips #1 screwdriver.

7. Replace the thermal switch.

8. To re-install, follow these steps in reverse order.

Replacing the power supply

To remove the power supply, complete the following steps.

1. Remove the top cover.

See

Removing the top cover

on page 51.

2. Remove the main board and I/O board.

See

Replacing the main board and I/O board

on page 69.

3. Remove the rear cover.

See

Removing the rear cover

on page 52.

4. Remove the left-side cover.

Summary of Contents for DHD630-GS
















































































Search results

Summary of Contents for DHD630-GS

Reviews:

Related manuals for DHD630-GS

Brands by name

Popular brands

Christie DHD630-GS, Service Manual

Search results

Summary of Contents for DHD630-GS

Reviews:

Related manuals for DHD630-GS

Brands by name

Popular brands