background image

Confirming command execution

If you want confirmation from the projector (or group of projectors) that a set message has been

processed, request an acknowledgment by inserting a dollar sign ($) after the start code left

parenthesis.
When the projector executes the command action (for example, as source switch), the projector
returns a dollar sign ($). This quickly confirms success with set messages and is particularly useful
with long-distance communication links or situations where the projectors or images are not visible
from the controller.
Set the active ILS file and return an acknowledgment example:

($ILF "ILS Flat")

$

Acknowledgments can also be a type of flow control.

Requesting an acknowledgment serves no purpose when included in a request message as the
acknowledgment is redundant to the reply from the projector. However, if requested, the dollar sign ($)
acknowledgment from the projector follows the reply.

Example:

($CHA?)

(CHA! "Media Block Flat")

$

Error messages

If a command cannot be performed, a descriptive error identifying the problem appears.
For example, the following message indicates a syntax error:

(65535 00000 ERR00005 "TMD+TIME: Too Few Parameters")

Communicating with the projector

C Technical Reference–Serial Commands

8

020-103075-05 Rev. 1 (09-2022)

Copyright 

©

 2022 Christie Digital Systems USA, Inc. All rights reserved.

If printed, please recycle this document after use.

Summary of Contents for CineLife+ 4 Series

































Reviews: