manualshive.com logo in svg

Christ 112991, Operating Manual

Share
Download
Christ 112991 Operating Manual Download Page 117

 

Freeze-dryer Epsilon 1-4 LSCplus 

Freeze-dryer Epsilon 2-4 LSCplus 

8 Maintenance and service 

 

 

 

Version 04/2014, Rev. 2.13 of 01/12/2021 

• sb 

117 / 148 

Translation of the original operating manual 

 

Pos :  248  /200 Chris t/360  GT-BA Labor-Pil ot ( STAND ARDMO DULE)/080 W artung und I nst andhaltung/ 080-0010- 0022-0020    Sonderauss tatt ung:  Tüv ersc hlus sriegel  aus  Edelst ahl   Epsil on @  25\mod_1404984677136_68. docx  @  185889  @ 4 @  1 

→

 

8.1.2.2 

Special equipment: Stainless steel door latch at the loading door 

Systems that are equipped with a stainless-steel or acrylic glass door with a 
stainless-steel door latch have a slide pad on the door latch. This slide pad 
is included in the scope of supply as a spare part. It must be inspected 
regularly for signs of wear. When its thickness is < 0.5 mm, it must be 
replaced. 

 

 

 

1

 

Door latch 

2

 

Slide pad 
(part no. 177270) 

3

 

Torx screws 

 

 

 

Fig. 77: Door latch and slide pad 

 

Replacing the slide pad: 

Unscrew the two screws of the slide pad with a Torx

®

 TX10 screwdriver, 

remove the old slide pad, and install the new one. 

Pos :  249  /010 Univ ers almodul e/                                                                                Leerz eile  @  0\mod_1202116244500_0.docx  @  114 @   @  1 

 

 

Pos :  250  /200 Chris t/361  GT-BA Labor-Pil ot ( PROJ EKTE)/ Epsilon  4er/ Epsilon  1-4_2- 4  LSC plus Standar d/ 080 W artung  und  Ins tandhalt ung/ 080- 0010- 0030    Belüft ungsv entil (nur  E2- 4) @  25\m od_1404984758394_68. docx  @  186127  @  3 @  1 

→

 

8.1.3 

Aeration valve 

Contaminants such as product residues may lead to an insufficient vacuum. 
In this case, the aeration valve must be cleaned. 
•  Switch the freeze-dryer off and disconnect the mains plug. 
•  Remove the valve core. 
•  Clean the valve core and the opening with a moist cloth. 
•  Clean the O-rings and inspect them for any damage. Damaged O-rings 

must be replaced. 

 

1

 

Valve opening 

2

 

Valve core 

3

 

O-rings 

       

 

Fig. 78: Valve opening and valve core with O-rings 
 

  (example, varies depending of the type of freeze-dryer) 

 

 

 

Summary of Contents for 112991





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands