Christ 102420 Page 39 Operating Manual Download

Page: 39 / 107

Freeze-dryer Beta 1-8 LSCbasic

Freeze-dryer Beta 2-8 LSCbasic

5 Set-up and connection

Version 03/2018, Rev. 1.5 of 09/03/2020

• sb-dc

39 / 107

Translation of the original operating manual

• Switch the unit off by actuating the mains power switch.
• Take the vacuum sensor out of its original packaging and fasten it to the

connector with a bow-shaped connecting piece, two clamping rings
(DIN16KF) and two centring rings (included in the scope of supply).

• Plug the connector to the connection socket and hand-tighten the

screws on the connector.

NOTE

It is absolutely essential to comply with the manufacturer’s instructions in
the separate operating manual of the vacuum sensor!

Thyracont VCP63 (Pirani)

Pfeiffer CMR 363 (capacitive)

Fig. 12: Vacuum sensors of different manufacturers

NOTE

The vacuum sensor comes supplied in a calibrated state.

After the freeze-dryer has been switched on, the vacuum sensor needs
several minutes until it is ready for operation.

Summary of Contents for 102420












































































































Search results

Summary of Contents for 102420

Reviews:

Related manuals for 102420

Brands by name

Popular brands

Christ 102420, Operating Manual

Search results

Summary of Contents for 102420

Reviews:

Related manuals for 102420

Brands by name

Popular brands