Christ 102420 Operating Manual Download Page 64 | Manualshive

Page: 64 / 107

Christ 102420 Operating Manual Download Page 64

Freeze-dryer Beta 1-8 LSCbasic

Freeze-dryer Beta 2-8 LSCbasic

6 Operation

64 / 107

Version 03/2018, Rev. 1.5 of 09/03/2020

• sb-dc

Translation of the original operating manual

6.5.1.3

Main window "?"

This main window includes the most important information concerning your
freeze-dryer:

1

Freeze-dryer type

2

Control system type

3

Serial number

4

Manufacturer contact
data

5

Details concerning the
software version

Fig. 48: Freeze-dryer system information (example)

NOTE

In the event of enquiries at the manufacturer, please state the data that is
stated here.

6.5.2

Starting a freeze-drying process

Freeze-drying processes are started in the main window "Process".

NOTE

Prior to any freeze-drying process, the correct method must be selected
(chapter 6.5.1.2 - " Main window "Options"", "Freeze-drying process (3)").

The set values for the individual process phases ("Freezing", "Warm-up",
"Main drying" and "Final drying") are defined prior to the start of the
process (see chapter 6.5.2.1 - "Entering set values"). Then, the freeze-
drying process can be started via the dialogue box "Operating mode:
select/start".

NOTE

If the freeze-drying process is to be started directly with the "Main drying"
phase, the vacuum pump must be warmed up approximately 15 minutes
prior to the process start. Failure to do so will result in a corresponding
warning message when the process starts.

«
...
62
63
64
65
66
...
»

Summary of Contents for 102420












































































































Reviews:

No comments