Chris-Craft 2014 32 Corsair RK Page 145 Owner'S Manual Download

Page: 145 / 234

Wash the area

To remove a gelcoat stain, begin by washing the affected area with soap and water. This alone will re-

move many stains, provided they are water-soluble. However, attempting to remove a mineral stain with

soap and water is a waste of time, because these stains are not water-soluble. Mineral stains require

products specifically formulated for their removal. These products usually contain an acid and/or a chelat-

ing (key-lay-ting) agent. Acids dissolve mineral stains while chelating agents chemically bond to the stain

and hold it in suspension until it is rinsed away. All feature simple spray- or wipe-on application and, be-

cause they rely on a chemical reaction, little or no scrubbing is required.

Stain removing products

Products tailored to remove organic and mineral stains on deck and rust around hardware include FSR by

Davis (Model 108753), Pure Oceans

Fiberglass Stain Remover

, and Rust Stain Remover (Model 126823)

by Starbrite. FSR and Fiberglass Stain Remover are non-runny gel formulations, making them excellent for

horizontal and vertical surfaces. Products such as Pure Oceans

Black Streak Cleaner

and 3M’s Black

Streak Remover (Model 3760212) are tailored to remove the “black streaks” described above. With their

simple spray- or wipe-on application, little or no scrubbing is required.

Heavy stains

Heavy waterline stains and the scum and calcium growth encountered at haul out require a more

aggressive approach. Products such as Mary Kate’s On & Off Hull/Bottom Cleaner (Model 127961) and are

strong acid formulations that really pack a punch. They are easily applied with a rag or brush and like other

acid-based products simply require that you wait a few minutes before rinsing them off. Because of their

caustic nature, rubber gloves and eye protection should be worn. Pure Oceans

Hull Cleaner

is a more en-

vironmentally friendly alternative that works well.

Restoring gelcoat shine

Once the stain is removed, take the time to apply a protective coat of wax to the gelcoat. This will provide a

barrier between staining materials and the pores in the gelcoat, making removal of future stains much eas-

ier. If your gelcoat still has a drab or chalky appearance after removing the stains, it is most likely suffering

from oxidation—so it is time for you to restore its shine!

Tools for making gelcoat shine

Before beginning, assemble the right tools. You will need a medium to coarse deck brush, a separate soft-

bristled brush, chamois and plenty of clean cotton rags. You will also need a pair of goggles to protect your

eyes and, because you will be working on your knees, you will also need protective kneepads. We suggest

Super-Soft Kneepads. These pads are big and comfy, with wide wrap-around straps for comfort while you

do the job.

Maintaining Your Boat’s Gelcoat Finish (Continued)

4-13

Storage And Commissioning

Summary of Contents for 2014 32 Corsair RK











































































































































































































































Search results

Summary of Contents for 2014 32 Corsair RK

Reviews:

Related manuals for 2014 32 Corsair RK

Brands by name

Popular brands

Chris-Craft 2014 32 Corsair RK, Owner'S Manual

Search results

Summary of Contents for 2014 32 Corsair RK

Reviews:

Related manuals for 2014 32 Corsair RK

Brands by name

Popular brands