background image

SKU 92455

      For technical questions, please call 1-800-444-3353.

Page 6

HEART PACEMAKER PRECAUTION

SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS

1.

      

 WARNING!   

People with pacemakers should consult their physician(s)

before using this product.  Electromagnetic fields in close proximity to a heart
pacemaker could cause interference to or failure of the pacemaker.

INSTALLATION PRECAUTIONS

1.

Ensure installation meets all applicable safety, and local and national electrical
codes.  Have installation performed by a qualified, licensed electrician and b u i l d -
ing contractor.

2.

All electrical work, including the earth-ground connection, should be completed by
a licensed electrician.

3.

Any separate fuel storage Generator supply facility must be built or installed in full
compliance with all relevant local, state, and federal regulations.

4.

If the generator is installed indoors, exhaust fumes must be piped out of the
building using leak-free, heat-resistant piping.  

Use the Generator only in

well ventilated outdoor areas.  Carbon monoxide fumes are a colorless,
odorless gas that, if inhaled, can cause serious injury or death.  

Pipes

and silencer should not use any flammable materials, nor should they be
installed near the same.  Generator exhaust fumes must be within legal lim-
its.

5.

If the generator is installed outdoors, it must be weatherproofed and should be sound-
proofed.  It should not be run outdoors without protection to the Generator and wir-
ing conduit.

6.

Never lift the Generator using the engine or alternator lifting lugs.  Connect lifting
equipment to the Frame of the Generator.

7.

Before lifting the Generator, ensure the lift rigging and supporting structure are in
good condition, and are rated to lift such a load.

8.

Keep all personnel away from the suspended generator while relocating.

9.

The supporting floor/ground surface should be level, and strong enough to safely
hold the weight of the Generator.  If the floor/ground surface is not level, strong cross
members should be placed under the full length of the Generator Frame at its low
side.

Summary of Contents for 92455

























Reviews: