Chicago Electric 69231 Owner'S Manual & Safety Instructions Download Page 1

ITEM 69231

7″ PORTABLE WET CUTTING

TILE SAW

Visit our website at: http://www.harborfreight.com

Email our technical support at: [email protected]

Read this material before using this product. 

Failure to do so can result in serious injury. 

SAVE THIS MANUAL.

Copyright

©

 2011 by Harbor Freight Tools

®

.  All rights reserved.  

No portion of this manual or any artwork contained herein may be reproduced in 

any shape or form without the express written consent of Harbor Freight Tools.  

Diagrams within this manual may not be drawn proportionally.  Due to continuing 

improvements, actual product may differ slightly from the product described herein.  

Tools required for assembly and service may not be included.

When unpacking, make sure that the product is intact 

and undamaged.  If any parts are missing or broken, 

please call 1-800-444-3353 as soon as possible.

Save This Manual

 

Keep this manual for the safety warnings and precautions, assembly, operating, 

inspection, maintenance and cleaning procedures.  Write the product’s serial number in the back of the manual 

near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and  

the receipt in a safe and dry place for future reference.

Owner’s Manual & Safety Instructions

REV 12a

Summary of Contents for 69231

















Reviews: