![Chicago Dryer King Edge Instruction Manual Download Page 113](http://html1.mh-extra.com/html/chicago-dryer/king-edge/king-edge_instruction-manual_2598167113.webp)
King Edge
Troubleshooting
6-21
WARNING
Only trained personnel with experience
in electrical or mechanical repair should
troubleshoot and repair the unit.
Troubleshooting
WARNING
Read the
REPAIR
chapter and make
sure that the power is disconnected
before doing any repairs.
ISSUE
POSSIBLE CAUSE
SOLUTION
(continued from previous page)
Upper Spreader Clamps Bang
or Drag at the Center of the Unit
3. Clamps are bouncing when
they are finished spreading.
Increase the SPREAD SLOW buffer
adjustment. Refer to the
CHI PANEL
OPERATION
bulletin,
Adjustment
section,
Spread Section Adjust-
ments
procedure.
•
4. The inverter may need to
be adjusted.
Adjust the inverter. Contact the fac-
tory Service Department.
•
Upper Spreader is not Reaching
the Center Home Position
1. Rubber stops at center of
machine out of position.
Check. Adjust as necessary.
•
2. Debris on the spread clamp
rail.
Check/clean as necessary.
•
3. Home sensor (PX12) needs
adjustment.
Adjust. Refer to the
REPAIR
chap-
ter,
Sensors
section,
Proximity
Sensor Positioning Adjustment
procedure.
•
Upper Spreader Speed Incon-
sistent
1. Taut sensors PE14 L/R
may be dirty, misaligned, or
defective.
Clean/adjust/replace as necessary.
For more information within this
chapter, refer to
Sensor Function
section.
•
2. INV3 malfunction.
Check inverter. Repair/replace as
necessary. For more information,
contact the factory Service Depart-
ment.
•
Excessive Spread Force on
Flatwork
1. SPREAD slow buffer is set
too low.
Increase. Refer to the
CHI PANEL
OPERATION
bulletin,
Adjustment
section,
Spreader Adjustments
procedure.
•
2. Torque is set too high.
Adjust TORQ setting. Refer to the
CHI PANEL OPERATION
bulletin,
Adjustment
section,
Program Ad-
justments (CHI)
procedure.
•
3. The inverter may need to
be adjusted.
Adjust the inverter. Contact the fac-
tory Service Department.
•
Too Little Spread Force on
Flatwork
(continued on next page)
1. Tension on upper spreader
belts needs adjustment.
Check. For more information, refer
to the
REPAIR
chapter,
Spreader
Section
section,
Upper Spreader
Belt Tension Adjustment
proce-
dure.
•
2. Spreader rail or rollers
need lubrication.
Lubricate. For more information,
refer to the
PREVENTIVE MAIN-
TENANCE
chapter,
Weekly PM
section,
Lubricate Upper Spreader
Rail, Carriage Rails and Rail Bear-
ings
procedure.
•
Summary of Contents for King Edge
