Chiayo STAGE PRO Operation Manual Download Page 27

 

26 

Maintenance-free Lead-acid and Lithium batteries 

6. Maintenance-free Lead-acid and Lithium batteries 

Cautions when using the battery 

1. 

Lead-acid batteries/lithium batteries have no memory effect. Please charge them up immediately after 
each use, no matter how much power they left. If the battery is not charged for a long time, it may cause 
the battery to be over-discharged and damaged, making it impossible to charge normally. 

2. 

U

sage temperature can’t be lower than -10°C nor higher than 50°C. 

3. 

It’s strictly forbidden to let the battery contact with any liquid. Do not immerse the battery in water or get it 
wet. After the battery is exposed to water, a decomposition reaction may occur, which may cause battery 
self-ignition or even cause an explosion.  

4. 

It is forbidden to use the battery when it has swelled, leaked, or the packaging is damaged. 

5. 

It is forbidden to disassemble the battery in any way or pierce the battery with a sharp object, so as not to 
cause the battery to catch fire or even cause an explosion.  

6. 

The liquid inside the battery is highly corrosive. If it leaks, please do not touch it. If the internal liquid 
splashes on human skin or eyes, please immediately rinse with clean water for at least 15 minutes before 
seeking medical attention.  

7. 

It is forbidden to use wires or other metal objects to short-circuit the positive and negative electrodes of 
the battery.  

 

Cautions when charging the battery 

1. 

Lead-acid batteries/lithium batteries have no memory effect. Please charge them up immediately after 
each use, no matter how much power they left. If the battery is not charged for a long time, it may cause 
the battery to be over-discharged and damaged, making it impossible to charge normally. 

2. 

Please use the power supply specified by CHIAYO for charging. 

3. 

The CHIAYO amplifier has a protection circuit to prevent overcharging. To ensure safety, the charging 
time should not exceed 12 hours. Please disconnect the power supply when fully charged. 

4. 

Charging temperature can’t be lower than 0°C nor higher than 40°C. 

5. 

When charging, please place it on the hard ground, such as cement, and there should be no flammable 
or combustible materials around. Please pay attention to the charging process to prevent accidents.  

6. 

It will automatically stop charging when fully charged. After the battery is fully charged, it is recommended 
to disconnect the amplifier from the power supply. 

7. 

When the power supply is not disconnected and the amplifier is not in use, if the battery is fully charged 
and then recharged again soon after, it means that the battery is aging and cannot store power. Please 
replace the battery to ensure enough time for operation.  

 

Cautions when storing the battery 

1. 

Lead-acid batteries/lithium batteries have no memory effect. Please charge them up immediately after 
each use, no matter how much power they left. If the battery is not charged for a long time, it may cause 
the battery to be over-discharged and damaged, making it impossible to charge normally. 

2. 

Lithium batteries will automatically discharge in storage. If they are not charged for a long time, they will 
over discharge that causes a decrease in capacity and damage to the batteries that can no longer be 
charged normally. It should be fully charged at least once every 6 months.  

3. 

Lead-acid batteries will automatically discharge in storage. If they are not charged for a long time, they 
will over discharge that causes a decrease in capacity and damage to the batteries that can no longer be 
charged normally. It should be fully charged at least once every 3 months.  

4. 

Storage temperature can’t be lower than -10°C nor higher than 40°C. 

 

Disposing the battery 

Be sure to completely discharge the battery before placing it in the designated battery recycling bin. 
Batteries contains dangerous chemicals. When disposing of old batteries, be sure to follow the local battery 
recycling and disposal regulations, and it is strictly forbidden to put them in a trash can.

 

 

 

Summary of Contents for STAGE PRO





























Reviews: