manualshive.com logo in svg

Chevrolet T-Series, Owner'S Manual

Share
Download
Chevrolet T-Series Owner'S Manual Download Page 95

The DRL system will make your headlamps come
on at reduced brightness when the following
conditions are met:

•

The ignition is on.

•

The headlamp band is in the OFF position.

•

The parking brake is released.

When the DRL are on, only your low-beam
headlamps will be on. The exterior lamps and
instrument panel will not be lit.

When it begins to get
dark, your DRL indicator
light is a reminder to
turn your headlamp
switch on.

The other lamps that come on with your
headlamps, will also come on.

When you turn the headlamp band to OFF, the
regular lamps will go off, and your low-beam
headlamps will change to the reduced brightness
of DRL.

To idle your vehicle with the DRL off, set the
parking brake. The DRL will stay off until
you release the parking brake.

As with any vehicle, you should turn on the
regular headlamp system when you need it.

Marker Lamps

If your vehicle is designed for trailer towing, this
button will operate the marker and clearance lamps.

The marker and
clearance lamp button is
located in the instrument
panel. See

Instrument

Panel Overview on
page 84

.

Press the button to turn the lamps on and press it
again to turn them off.

The headlamp band will not operate these lamps.

95

Summary of Contents for T-Series







































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands