manualshive.com logo in svg

Chevrolet T-Series, Owner'S Manual

Share
Download
Chevrolet T-Series Owner'S Manual Download Page 56

High Idle System

Manual High Idle System

If your vehicle has this
feature, the manual high
idle button is located
in the instrument panel.
See

Instrument Panel

Overview on page 84

for more information.

This system can be used to increase your engine
idle speed whenever the following conditions
are met:

•

The brake pedal is not pressed.

•

The vehicle is at a complete stop.

•

The manual transmission clutch pedal is not
pressed or, the automatic transmission is in
NEUTRAL (N) or PARK (P).

The manual high idle feature is activated by
pressing the button on the instrument panel. When
the button is pressed again, or any of the
previous conditions are not met, manual high idle
will be deactivated.

56

Summary of Contents for T-Series







































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands