manualshive.com logo in svg

Chevrolet T-Series, Owner'S Manual

Share
Download
Chevrolet T-Series Owner'S Manual Download Page 254

Instrument Panel Fuse Block

The instrument panel fuse block is located on the
top of the instrument panel on the passenger’s
side of the vehicle.

To access the fuse block, remove the cover by
lifting up on the front and turning it backward.

To reinstall the cover, put the tabs at the rear
of the cover into the slots on the instrument
panel and lower the cover down to snap
into place.

If you ever have a problem on the road and don’t
have a spare fuse, you can borrow one of the
correct value. Just pick some feature of your
vehicle that you can get along without, like the
radio or cigarette lighter, and use its fuse if it is the
value you need. Remember to replace the fuse
as soon as you can.

These fuses are non-cycling; do not replace them
with cycling fuses. Also, do not use fuses of a
higher amperage than those listed on the circuit
breaker block.

254

Summary of Contents for T-Series







































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands