manualshive.com logo in svg

Chevrolet T-Series, Owner'S Manual

Share
Download
Chevrolet T-Series Owner'S Manual Download Page 221

What to Use

Refer to the Maintenance Schedule to determine
what kind of lubricant to use. See

Part C:

Recommended Fluids and Lubricants on page 295

.

Rear Axle Shift Motor

When to Check and Change Fluid

If you have an optional air-shift two-speed,
controlled traction, or locking differential type rear
axle, a good time to check the fluid level in the
axle shift motor is when the rear axle lubricant is
checked.

How to Check Fluid

Remove the plug on the front plate of the axle
shift motor, add enough fluid to raise the level to
the bottom of the filler plug hole, then replace
the plug.

What to Use

Refer to your Maintenance Schedule to determine
what kind of lubricant to use. See

Part C:

Recommended Fluids and Lubricants on page 295

.

Cab Tilting

Before You Tilt the Cab

Most fluids and lubricants requiring regular
checking can be accessed at the back of the cab. If
you need to gain access to components under the
cab, follow this entire procedure carefully.

•

Find a level place to tilt the cab.

•

Secure all loose articles in the cab and close
the cab door.

•

Check for adequate clearance in front and
above the cab.

To help prevent the vehicle from moving:

1. Apply the parking brake.

2. Place the automatic transmission in PARK (P)

or shift the manual transmission to NEUTRAL.

3. Turn the engine off.

4. Block the front and rear wheels.

221

Summary of Contents for T-Series







































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands