manualshive.com logo in svg

Chevrolet T-Series, Owner'S Manual

Share
Download
Chevrolet T-Series Owner'S Manual Download Page 17

With safety belts, you slow down as the vehicle
does. You get more time to stop.

You stop over more distance, and your strongest
bones take the forces. Safety belts are for
everyone.

Questions and Answers About
Safety Belts

Q:

Will I be trapped in the vehicle after an
accident if I am wearing a safety belt?

A:

You

could

be — whether you are wearing a

safety belt or not. But you can unbuckle a
safety belt, even if you are upside down. And
your chance of being conscious during and
after an accident, so you

can

unbuckle and get

out, is

much

greater if you are belted.

Q:

If I am a good driver, and I never drive far
from home, why should I wear safety belts?

A:

You may be an excellent driver, but if you are
in an accident — even one that is not your
fault — you and your passengers can be hurt.
Being a good driver does not protect you
from things beyond your control, such as
bad drivers.

Most accidents occur within 25 miles (40 km) of
home. And the greatest number of serious
injuries and deaths occur at speeds of less than
40 mph (65 km/h).
Safety belts are for everyone.

17

Summary of Contents for T-Series







































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands