manualshive.com logo in svg

Chevrolet T-Series, Owner'S Manual

Share
Download
Chevrolet T-Series Owner'S Manual Download Page 128

A non-scrubbing action, wet-type cleaner which
uses a cassette with a fabric belt to clean the tape
head can be used. This type of cleaning cassette
will not eject on its own. A non-scrubbing
action cleaner may not clean as thoroughly as the
scrubbing type cleaner. The use of a
non-scrubbing action, dry-type cleaning cassette is
not recommended.

Cassettes are subject to wear and the sound
quality may degrade over time. Always make sure
the cassette tape is in good condition before
the tape player is serviced.

Fixed Mast Antenna

The antenna is located in front of the driver’s side
door at the top of the cab. Push the antenna
back in to retract it. The antenna should be
retracted when entering low clearance areas.

128

Summary of Contents for T-Series







































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands