Chevrolet T-Series Owner'S Manual Download Page 12 | Manualshive

Page: 12 / 326

Chevrolet T-Series Owner'S Manual Download Page 12

Air Suspension Seats

Your vehicle may have an air suspension seat.
There are two ways you can adjust the seat.

Height Adjustment

The height adjustment
is controlled by the air
suspension valve.
The lever for the valve
is located on the
outboard side of the
driver’s seat.

Pull the lever up to raise the seat. Push the lever
down to lower the seat.

Isolator Lock Lever

The lever is located on
the inboard side of the
driver’s seat.

Move the handle down to lock the seat in place.
This is used to reduce backslap experienced while
in tractor/trailer operation or while operating a
dump truck.

Lever shown in the

Locked Position

12

«
...
10
11
12
13
14
...
»

Summary of Contents for T-Series







































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands