manualshive.com logo in svg

Chevrolet Silverado 2020, Owner'S Manual

Share
Download
Chevrolet Silverado 2020 Owner'S Manual Download Page 357

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-

13337620) - 2020 - CTC - 1/27/20

356

Vehicle Care

For vehicles not equipped with the
Stop/Start system:

1. Loosen the negative battery

cable nut (1).

2. Remove the negative battery

cable clamp (2) from the
negative battery post.

3. Cover the negative battery

cable clamp, and negative
battery post with a
non-conductive material to
prevent any contact with the
negative battery cable.

Negative Battery Cable
Reconnection

Caution

When reconnecting the battery:

.

Use the original nut from the
vehicle to secure the
negative battery cable. Do
not use a different nut.
If you need a replacement
nut, see your dealer.

.

Tighten the nut with a hand
tool. Do not use an impact
wrench or power tools to
tighten the nut.

The vehicle could be damaged if
these guidelines are not followed.

Caution

Do not use paints, lubricants,
or corrosion inhibitors on the nut
that secures the negative battery
cable to the vehicle. This could
damage the vehicle.

For vehicles equipped with the Stop/
Start system:

1. Install the negative battery

cable to the battery
sensor stud.

2. Install the negative battery

cable nut to the battery sensor
stud and tighten.

3. Turn the ignition on.

For vehicles not equipped with the
Stop/Start system:

1. Install the negative battery

cable clamp to the negative
battery post.

2. Tighten the negative battery

cable nut.

3. Turn the ignition on.

Four-Wheel Drive

Transfer Case

When to Check Lubricant

Refer to

Maintenance Schedule

0

437

to determine when to check

the lubricant.

Summary of Contents for Silverado 2020
















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands