manualshive.com logo in svg

Chevrolet Silverado 2020, Owner'S Manual

Share
Download
Chevrolet Silverado 2020 Owner'S Manual Download Page 214

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-

13337620) - 2020 - CTC - 1/27/20

Driving and Operating

213

Warning (Continued)

vehicle. Possible heater
cord and thermostat
damage could occur.

.

While in use, do not let the
heater cord touch vehicle
parts or sharp edges. Never
close the hood on the
heater cord.

.

Before starting the vehicle,
unplug the cord, reattach
the cover to the plug, and
securely fasten the cord.
Keep the cord away from
any moving parts.

5. Before starting the engine, be

sure to unplug and store
the cord.

The length of time the heater should
remain plugged in depends on
several factors. Ask a dealer in the
area where you will be parking the
vehicle for the best advice on this.

Retained Accessory
Power (RAP)

When the ignition is turned from on
to off, the following features (if
equipped) will continue to function
for up to 10 minutes, or until the
driver door is opened. These
features will also work when the
ignition is in RUN or ACC/
ACCESSORY:

.

Infotainment System

.

Power Windows (during RAP
this functionality will be lost
when any door is opened)

.

Sunroof (during RAP this
functionality will be lost when
any door is opened)

.

Auxiliary Power Outlet

.

Audio System

.

OnStar System

Shifting Into Park

{

Warning

It can be dangerous to get out of
the vehicle if the shift lever is not
fully in P (Park) with the parking
brake firmly set. The vehicle can
roll. If you have left the engine
running, the vehicle can move
suddenly. You or others could be
injured. To be sure the vehicle will
not move, even when you are on
fairly level ground, use the steps
that follow. With four-wheel drive,
if the transfer case is in
N (Neutral), the vehicle will be
free to roll, even if the shift lever
is in P (Park). Be sure the transfer
case is in a drive gear. If towing a
trailer, see

Driving Characteristics

and Towing Tips

0

283

.

1. Hold the brake pedal down,

then set the parking brake. See

Electric Parking Brake

0

229

.

Summary of Contents for Silverado 2020
















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands