manualshive.com logo in svg

Chevrolet Silverado 2020, Owner'S Manual

Share
Download
Chevrolet Silverado 2020 Owner'S Manual Download Page 208

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-

13337620) - 2020 - CTC - 1/27/20

Driving and Operating

207

the brake pedal applied, pressing
ENGINE START/STOP button once
will turn the ignition on. Once engine
cranking begins, release the button.
Engine cranking will continue until
the engine starts. See

Starting the

Engine

0

209

.

Service Mode

This power mode is available for
service and diagnostics, and to
verify the proper operation of the
malfunction indicator lamp as may
be required for emission inspection
purposes. With the vehicle off, and
the brake pedal not applied,
pressing and holding the ENGINE
START/STOP button for more than
five seconds will place the vehicle in
Service Mode. The instruments and
audio systems will operate as they
do when the ignition is on, but the
vehicle will not be able to be driven.
The engine will not start in Service
Mode. Press the ENGINE START/
STOP button again to turn the
ignition off.

Ignition Positions (Key
Access)

0. Stopping the Engine/LOCK/OFF

1. ACC/ACCESSORY

2. ON/RUN

3. START

The ignition switch has four
positions.

To shift out of P (Park), the ignition
must be ON/RUN and the brake
pedal must be applied.

0 (Stopping the Engine/LOCK/
OFF) :

This position turns off the

vehicle. It also locks the ignition, the
transmission, and the steering
column, if equipped with a locking
steering column.

To turn off the vehicle:

1. Make sure that the vehicle is

stopped.

2. Shift to P (Park).

3. Continue to hold the brake

pedal, then set the parking
brake. See

Electric Parking

Brake

0

229

.

Summary of Contents for Silverado 2020
















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands