manualshive.com logo in svg

Chevrolet Express 2012, Owner'S Manual

Share
Download
Chevrolet Express 2012 Owner'S Manual Download Page 342

Black plate (92,1)

Chevrolet Express Owner Manual - 2012 - crc - 11/11/11

10-92

Vehicle Care

Care of Safety Belts

Keep belts clean and dry.

{

WARNING

Do not bleach or dye safety belts.
It may severely weaken them. In
a crash, they might not be able to
provide adequate protection.
Clean safety belts only with mild
soap and lukewarm water.

Floor Mats

{

WARNING

If a floor mat is the wrong size or
is not properly installed, it can
interfere with the pedals.
Interference with the pedals can
cause unintended acceleration
and/or increased stopping
distance which can cause a crash
and injury. Make sure the floor
mat does not interfere with the
pedals.

Use the following guidelines for
proper floor mat usage.

.

The original equipment floor
mats were designed for the
vehicle. If the floor mats need
replacing, it is recommended
that GM certified floor mats be
purchased. Non-GM floor mats
may not fit properly and may
interfere with the pedals. Always
check that the floor mats do not
interfere with the pedals.

.

Use the floor mat with the
correct side up. Do not turn
it over.

.

Do not place anything on top of
the driver side floor mat.

.

Use only a single floor mat on
the driver side.

.

Do not place one floor mat on
top of another.

Summary of Contents for Express 2012





















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands